DocumentationGrafana documentationAlertingSet upConfigure high availability

Configure high availability

Grafana Alerting uses the Prometheus model of separating the evaluation of alert rules from the delivering of notifications. In this model, the evaluation of alert rules is done in the alert generator and the delivering of notifications is done in the alert receiver. In Grafana Alerting, the alert generator is the Scheduler and the receiver is the Alertmanager.

When running multiple instances of Grafana, all alert rules are evaluated on all instances. You can think of the evaluation of alert rules as being duplicated by the number of running Grafana instances. This is how Grafana Alerting makes sure that as long as at least one Grafana instance is working, alert rules are still be evaluated and notifications for alerts are still sent.

You can find this duplication in state history and it is a good way to confirm if you are using high availability.

While the alert generator evaluates all alert rules on all instances, the alert receiver makes a best-effort attempt to avoid sending duplicate notifications. Alertmanager chooses availability over consistency, which may result in occasional duplicated or out-of-order notifications. It takes the opinion that duplicate or out-of-order notifications are better than no notifications.

The Alertmanager uses a gossip protocol to share information about notifications between Grafana instances. It also gossips silences, which means a silence created on one Grafana instance is replicated to all other Grafana instances. Both notifications and silences are persisted to the database periodically, and during graceful shut down.

Enable alerting high availability using Memberlist

Before you begin

Since gossiping of notifications and silences uses both TCP and UDP port 9094, ensure that each Grafana instance is able to accept incoming connections on these ports.

To enable high availability support:

1. In your custom configuration file ($WORKING_DIR/conf/custom.ini), go to the [unified_alerting] section.
2. Set [ha_peers] to the number of hosts for each Grafana instance in the cluster (using a format of host:port), for example, ha_peers=10.0.0.5:9094,10.0.0.6:9094,10.0.0.7:9094. You must have at least one (1) Grafana instance added to the ha_peers section.
3. Set [ha_listen_address] to the instance IP address using a format of host:port (or the Pod’s IP in the case of using Kubernetes). By default, it is set to listen to all interfaces (0.0.0.0).
4. Set [ha_peer_timeout] in the [unified_alerting] section of the custom.ini to specify the time to wait for an instance to send a notification via the Alertmanager. The default value is 15s, but it may increase if Grafana servers are located in different geographic regions or if the network latency between them is high.

Enable alerting high availability using Redis

As an alternative to Memberlist, you can use Redis for high availability. This is useful if you want to have a central database for HA and cannot support the meshing of all Grafana servers.

1. Make sure you have a Redis server that supports pub/sub. If you use a proxy in front of your Redis cluster, make sure the proxy supports pub/sub.
2. In your custom configuration file ($WORKING_DIR/conf/custom.ini), go to the [unified_alerting] section.
3. Set ha_redis_address to the Redis server address Grafana should connect to.
4. Optional: Set the username and password if authentication is enabled on the Redis server using ha_redis_username and ha_redis_password.
5. Optional: Set ha_redis_prefix to something unique if you plan to share the Redis server with multiple Grafana instances.
6. Optional: Set ha_redis_tls_enabled to true and configure the corresponding ha_redis_tls_* fields to secure communications between Grafana and Redis with Transport Layer Security (TLS).

The following metrics can be used for meta monitoring, exposed by the /metrics endpoint in Grafana:

Enable alerting high availability using Kubernetes

1. You can expose the Pod IP through an environment variable via the container definition.

   yaml Copy

   env:
     - name: POD_IP
       valueFrom:
         fieldRef:
           fieldPath: status.podIP

2. Add the port 9094 to the Grafana deployment:

   yaml Copy

   ports:
     - containerPort: 3000
       name: http-grafana
       protocol: TCP
     - containerPort: 9094
       name: grafana-alert
       protocol: TCP

3. Add the environment variables to the Grafana deployment:

   yaml Copy

   env:
     - name: POD_IP
       valueFrom:
         fieldRef:
           fieldPath: status.podIP

4. Create a headless service that returns the Pod IP instead of the service IP, which is what the ha_peers need:

   yaml Copy

   apiVersion: v1
   kind: Service
   metadata:
     name: grafana-alerting
     namespace: grafana
     labels:
       app.kubernetes.io/name: grafana-alerting
       app.kubernetes.io/part-of: grafana
   spec:
     type: ClusterIP
     clusterIP: 'None'
     ports:
       - port: 9094
     selector:
       app: grafana

5. Make sure your grafana deployment has the label matching the selector, e.g. app:grafana:

6. Add in the grafana.ini:

   bash Copy

   [unified_alerting]
   enabled = true
   ha_listen_address = "${POD_IP}:9094"
   ha_peers = "grafana-alerting.grafana:9094"
   ha_advertise_address = "${POD_IP}:9094"
   ha_peer_timeout = 15s